 |
 |
| |
| 龙丘智能奉献LCD1602液晶MC9S12XS128代码一份，接口说明详细 |
|
[ 2010-12-8 13:18:00 | By: 龙丘 ] |
Code Warrior 5.0
Target : MC9S12XS128
Crystal: 16.000Mhz
busclock: 8.000MHz
pllclock:16.000MHz
============================================
液晶管脚接线定义
PIN1 GND
PIN2 5V
PIN3 10K电阻接地
PIN4 LCD1602_RS PORTB_PB0 //Data Command Pin 1 data 0 command
PIN5 LCD1602_RW PORTB_PB1 //Read Write Pin 1 read 0 write
PIN6 LCD1602_EN PORTB_PB2 //LCD Enable Signal
PIN7-14 LCDIO PORTA
------------------------------------------------------
主题函数如下图，完整工程参考附件：  LQ_XS_LCD1602.rar (60.72 KB)
＃i nclude "derivative.h"
＃i nclude "LQ1602.h"
void LcdInit(){
DDRA = 0xff;
DDRB = 0xff;
LCDIO_DIR = LCDIO_DIR_OUT;
LcdDelay();
LcdCommand(CLR,0); //clear screen
LcdCommand(DATA_MODE,1); //set 8 bit data transmission mode
LcdCommand(INPUTMODE_CUR_R | INPUTMODE_ALL_D, 1); // cursor right, disable moving
LcdCommand(SCREEN_OPEN | SCREEN_OPEN_CUR | SCREEN_OPEN_TWI, 1); //open display (enable lcd display)
LcdCommand(LINE1_HEAD,1); //set lcd first display address
LcdCommand(CLR,1); //clear screen
}
////////////////////////////////////////////////////////////////////
// write command
//
void LcdCommand(byte command,byte BusyC){
if (BusyC) ReadStatus(); //Test it busy or not
LCDIO=command;
LCD1602_RS=0;
LCD1602_RW=0;
LCD1602_EN=0;
LCD1602_EN=0;
LCD1602_EN=1;
}
byte ReadStatus(void)
{
byte cRtn;
LCDIO_DIR = LCDIO_DIR_IN;
LCD1602_RS = 0;
LCD1602_RW = 1;
LCD1602_EN = 0;
LCD1602_EN = 0;
LCD1602_EN = 1;
while (LCDIO & BUSY); //Test Busy State
cRtn = LCDIO_DIR; // if Not save the port value, it should be change
LCDIO_DIR = LCDIO_DIR_OUT;
return(cRtn);
}
void LcdDelay(void)
{
word i, j;
for (i = 0; i < 300; i++)
for(j = 0; j < 3000; j++);
}
void LcdClear(void)
{
LcdCommand(CLR,1); //clear screen
}
////////////////////////////////////////////////////////////////////
// write data
//
void LcdData(byte dat,byte BusyC)
{
if (BusyC) ReadStatus(); //Test it busy or not
LCDIO=dat;
LCD1602_RS=1;
LCD1602_RW=0;
LCD1602_EN=0;
LCD1602_EN=0;
LCD1602_EN=1;
}
////////////////////////////////////////////////////////////////////
// write lcd a character
//
void LcdWriteChar( byte x,byte y,byte dat){
LcdSetXY(x, y);
LcdData(dat,1);
}
////////////////////////////////////////////////////////////////////
// set display address
//
void LcdSetXY( byte x, byte y ){
byte address;
if (y == LINE1)
address = LINE1_HEAD + x;
else
address = LINE2_HEAD + x;
LcdCommand(address,1);
}
////////////////////////////////////////////////////////////////////
// write lcd string
//
void LcdWriteStr(byte X,byte Y,char *s)
{
LcdSetXY( X, Y ); //set address
while (*s) // write character
{
LcdData(*s, 1);
s++;
}
} | |
|
| |
|
